NJ Zoning Check

Washington Borough zoning check

Enter your address to find your zone and see if your project fits. No account needed.

About these numbers

Enter a lot in Washington Borough's R-1, R-2 or R-3 Residence District and see, line by line, whether a house, addition or detached garage or shed meets the Borough's lot, yard, height and size limits. The check is free.

Covers the Borough of Washington's single-family zones R-1, R-2, R-3 and R-3-2F, Warren County. Checks a new house, an addition, an attached garage or a detached garage or shed.

Numbers last checked November 16, 2026 against the residence district sections of the Borough's zoning chapter.

Check a different address

We send the address to New Jersey's public parcel records and public zoning maps to find your lot. Privacy

Know your zone? Leave the address blank.Detailed check for architects and contractors

What you can build in Washington Borough

Washington Borough has 4 single-family zones covered here: R-1, R-2, R-3 and R-3-2F. Minimum lot sizes run from 6,250 sq ft (R-3) to 17,500 sq ft (R-1) in most zones. A house must sit 25 ft (R-3) to 50 ft (R-1) back from the street and 25 ft (R-3) to 50 ft (R-1) from the rear lot line. Houses can be up to 35 ft tall.

New house or addition

Depends on your zone. Your address will show your exact numbers.

From the street
25 to 50 ft
From each side
6 ft in most zones
From the back
25 to 50 ft
Height
35 ft
See the limits for every zone
ZoneFrontEach sideRearHeight
R-1Lots of 17,500 sq ft50 ftVaries50 ft35 ft, 2.5 stories
R-2Lots of 11,250 sq ft40 ftVaries40 ft35 ft, 2.5 stories
R-3Lots of 6,250 sq ft25 ft6 ft25 ft35 ft, 2.5 stories
R-3-2F25 ft6 ft25 ft35 ft, 2.5 stories
  • Varies means the limit depends on details of your lot. Check your address to see what we can work out.

Sheds and detached garages have their own rules. Enter your address above to see them.

Standard limits for single-family lots. Corner lots and special rules can change them. Last checked November 16, 2026. Confirm with the town before you design or buy.

Washington Borough zoning questions

What are the setbacks in Washington Borough, NJ?

For a single-family house. Corner lots can differ.

  • R-1: 50 ft from the street, 50 ft from the rear line.
  • R-2: 40 ft from the street, 40 ft from the rear line.
  • R-3: 25 ft from the street, 6 ft on each side, 25 ft from the rear line.
  • R-3-2F: 25 ft from the street, 6 ft on each side, 25 ft from the rear line.

What is the minimum lot size in Washington Borough?

R-1: 17,500 sq ft; R-2: 11,250 sq ft; R-3: 6,250 sq ft. In the other zones it depends on the lot.

How tall can a house be in Washington Borough?

R-1: 35 ft, 2.5 stories; R-2: 35 ft, 2.5 stories; R-3: 35 ft, 2.5 stories; R-3-2F: 35 ft, 2.5 stories.

Can you recommend an architect in Washington Borough?

Yes. Tell us about your project and we'll connect you with a vetted, licensed residential architect who works in Washington Borough. It's free and there's no obligation.

We'll connect you with a vetted, licensed residential architect who works in Washington Borough and can turn what your lot allows into drawings for your permit. Free, with no obligation.

Get a free architect referral

Zoning table for your drawings

ITEMREQUIREDEXISTINGPROPOSEDCOMPLIES

ENC = existing nonconforming condition, not increased. * = relief required.

Prepared with a calculation aid. Not a zoning determination. Confirm every requirement with the municipal zoning officer.

What this does not check

Where the numbers come from

Requirements were entered on November 16, 2026 from the Borough of Washington's Chapter 94, Zoning and Land Development, Sections 94-37 and 94-75 to 94-77. Check every requirement against the current code before relying on it.

A calculation aid, not a zoning determination. Using this site means you agree to the terms of use; see also the privacy policy.

Pick a zone to startSee the table